- HTTPProxy Fundamentals
- Virtual Hosts
- Inclusion and Delegation
- TLS Termination
- Upstream TLS
- Request Routing
- External Service Routing
- Request Rewriting
- Upstream Health Checks
- Client Authorization
- TLS Delegation
- Rate Limiting
- Access logging
- Annotations Reference
- API Reference
- Deployment Options
- Contour Configuration
- Upgrading Contour
- Enabling TLS between Envoy and Contour
- Redeploy Envoy
- AWS with NLB
- External Authorization
- JSON logging
- Migrating to HTTPProxy
- Prometheus Metrics
- PROXY Protocol Support
- Resource Limits
- Envoy Administration Access
- Contour Debug Logging
- Envoy Debug Logging
- Visualize the Contour Graph
- Show Contour xDS Resources
- Profiling Contour
- Contour Operator
- Support Policy
- Compatibility Matrix
- Contour Deprecation Policy
- Release Process
- Frequently Asked Questions
Contour supports integrating external servers to authorize client requests.
Envoy implements external authorization in the ext_authz filter. This filter intercepts client requests and holds them while it sends a check request to an external server. The filter uses the check result to either allow the request to proceed, or to deny or redirect the request.
The diagram below shows the sequence of requests involved in the successful authorization of a HTTP request:
The external authorization guides demonstrates how to deploy HTTP basic authentication using Contour and contour-authserver.
The starting point for external authorization in Contour is the ExtensionService API. This API creates a cluster which Envoy can use to send requests to an external server. In principle, the Envoy cluster can be used for any purpose, but in this document we are concerned only with how to use it as an authorization service.
An authorization service is a gRPC service that implements the Envoy CheckRequest protocol. Note that Contour requires the extension to implement the “v3” version of the protocol. Contour is compatible with any authorization server that implements this protocol.
The primary field of interest in the
ExtensionService CRD is the
This field lists the Kubernetes Services that will receive the check requests.
.spec.services.name field contains the name of the Service, which must
exist in the name namespace as the
ExtensionService object must exist in the name namespace as the
Services they target to ensure that both objects are under the same
Load Balancing for Extension Services
ExtensionService can be configured to send traffic to multiple Kubernetes Services.
In this case, requests are divided proportionally across the Services according
to the weight in the
The service weight can be used to flexibly shift traffic between Services for
reasons like implementing blue-green deployments.
.spec.loadBalancerPolicy field configures how Envoy will load balance
requests to the endpoints within each Service.
TLS Validation for Extension Services
Since authorizing a client request may involve passing sensitive credentials
from a HTTP request to the authorization service, the connection to the
authorization server should be as secure as possible.
Contour defaults the
.spec.protocol field to “h2”, which configures
Envoy to use HTTP/2 over TLS for the authorization service connection.
.spec.validation field configures how Envoy should verify the TLS
identity of the authorization server.
This is a critical protection against accidentally sending credentials to an
imposter service and should be enabled for all production deployments.
.spec.validation field should specify the expected server name
from the authorization server’s TLS certificate, and the trusted CA bundle
that can be used to validate the TLS chain of trust.
Authorizing Virtual Hosts
.spec.virtualhost.authorization field in the Contour
API connects a virtual host to an authorization server that is bound by an
Each virtual host can use a different
ExtensionService, but only one
ExtensionService can be used by a single virtual host.
Authorization servers can only be attached to
HTTPProxy objects that have TLS
Migrating from Application Authorization
When applications perform their own authorization, migrating to centralized
authorization may need some planning.
.spec.virtualhost.authorization.failOpen field controls how client
requests should be handled when the authorization server fails.
During a migration process, this can be set to
true, so that if the
authorization server becomes unavailable, clients can gracefully fall back to
the existing application authorization mechanism.
Scoping Authorization Policy Settings
It is common for services to contain some HTTP request paths that require authorization and some that do not. The HTTPProxy authorization policy allows authorization to be disabled for both an entire virtual host and for specific routes.
The initial authorization policy is set on the HTTPProxy virtual host
This configures whether authorization is enabled, and the default authorization policy context.
If authorization is disabled on the virtual host, it is also disabled by
default on all the routes for that virtual host that do not specify an authorization policy.
However, a route can configure its own authorization policy (in the
.spec.routes.authPolicy field) that can configure whether authorization
is enabled, irrespective of the virtual host setting.
The authorization policy context is a way to configure a set of key/value pairs that will be sent to the authorization server with each request check request. The keys and values that should be specified here depend on which authorization server has been configured. This facility is intended for configuring authorization-specific information, such as the basic authentication realm, or OIDC parameters.
The initial context map can be set on the virtual host. This sets the context keys that will be sent on every check request. A route can overwrite the value for a context key by setting it in the context field of authorization policy for the route.